Novel multimethod approach for the determination of the colloidal stability of nanomaterials in complex environmental mixtures using a global stability index: TiO2 as case study.

A systematic study on the colloidal behavior of uncoated and polyvinylpyrrolidone (PVP) coated TiO2 engineered nanomaterials (ENMs) in simulated aqueous media is herein reported, in which conditions representative for natural waters (pH, presence of divalent electrolytes (i.e. Ca2+/Mg2+ and SO42-), of natural organic matter (NOM) and of suspended particulate matter (SPM)) were systematically varied. The colloidal stability of the different dispersions was investigated by means of Dynamic and Electrophoretic Light Scattering (DLS and ELS) and Centrifugal Separation Analysis (CSA), and a global stability index based on these three techniques was developed. The index allows to quantitatively classify the nano-based dispersions according to their colloidal stability affected by the different parameters studied. This multimethod approach clearly identifies inorganic SPM followed by divalent electrolytes as the main natural components destabilizing TiO2 ENMs upon entering in simulated natural waters, while it highlights a moderate stabilization induced by NOM, depending mainly on pH. Moreover, the PVP coating was found to attenuate the influence of these parameters on the colloidal stability. The obtained results show how the global stability index developed is influenced by the complexity of the system, suggesting the importance of combining the information gathered from all the techniques employed to better elucidate the fate and behavior of ENMs in natural surface waters.

Characterizing the behavior, uptake, and toxicity of NM300K silver nanoparticles in Caenorhabditis elegans.

Using Caenorhabditis elegans as a model organism, we addressed the potential linkage among toxicity of NM300K Ag nanoparticles (AgNPs), their particle size distribution, and the presence of dissolved Ag in the test media. Of the 3 endpoints assessed (growth, fertility, and reproduction), reproduction was the most sensitive, with the 50% effect concentration (EC50) ranging from 0.26 to 0.84 mg Ag L-1 and 0.08 to 0.11 mg Ag L-1 for NM300K and AgNO3 , respectively. Silver uptake by C. elegans was similar for both forms of Ag, whereas bioaccumulation was higher in AgNO3 exposure. The observed differences in toxicity between NM300K and AgNO3 did not correlate with bioaccumulated Ag, which suggests that toxicity is a function of the type of exposing agent (AgNPs vs AgNO3 ) and its mode of action. Before addition of the food source (Escherichia coli), size fractionation revealed that dissolved Ag comprised 13 to 90% and 4 to 8% of total Ag in the AgNO3 and NM300K treatments, respectively. No dissolved Ag was detectable in the actual test media due to immediate Ag adsorption to bacteria. The results of the present study indicate that information on behavior and characterization of exposure conditions is essential for nanotoxicity studies. Environ Toxicol Chem 2018;37:1799-1810. © 2018 SETAC.

Influence of organic molecules on the aggregation of TiO2 nanoparticles in acidic conditions.

Engineered nanoparticles released into the environment may interact with natural organic matter (NOM). Surface complexation affects the surface potential, which in turn may lead to aggregation of the particles. Aggregation of synthetic TiO2 (anatase) nanoparticles in aqueous suspension was investigated at pH 2.8 as a function of time in the presence of various organic molecules and Suwannee River fulvic acid (SRFA), using dynamic light scattering (DLS) and high-resolution transmission electron microscopy (TEM). Results showed that the average hydrodynamic diameter and ζ-potential were dependent on both concentration and molecular structure of the organic molecule. Results were also compared with those of quantitative batch adsorption experiments. Further, a time study of the aggregation of TiO2 nanoparticles in the presence of 2,3-dihydroxybenzoic acid (2,3-DHBA) and SRFA, respectively, was performed in order to observe changes in ζ-potential and particle size over a time period of 9 months. In the 2,3-DHBA-TiO2 system, ζ-potentials decreased with time resulting in charge neutralization and/or inversion depending on ligand concentration. Aggregate sizes increased initially to the micrometer size range, followed by disaggregation after several months. No or very little interaction between SRFA and TiO2 occurred at the lowest concentrations tested. However, at the higher concentrations of SRFA, there was an increase in both aggregate size and the amount of SRFA adsorbed to the TiO2 surface. This was in correlation with the ζ-potential that decreased with increased SRFA concentration, leading to destabilization of the system. These results stress the importance of performing studies over both short and long time periods to better understand and predict the long-term effects of nanoparticles in the environment.

Intermethod comparison of the particle size distributions of colloidal silica nanoparticles.

There can be a large variation in the measured diameter of nanoparticles depending on which method is used. In this work, we have strived to accurately determine the mean particle diameter of 30-40 nm colloidal silica particles by using six different techniques. A quantitative agreement between the particle size distributions was obtained by scanning electron microscopy (SEM), and electrospray-scanning mobility particle sizer (ES-SMPS). However, transmission electron microscopy gave a distribution shifted to smaller sizes. After confirming that the magnification calibration was consistent, this was attributed to sample preparation artifacts. The hydrodynamic diameter, dh , was determined by dynamic light scattering (DLS) both in batch mode, and hyphenated with sedimentation field flow fractionation. Surprisingly the dh were smaller than the SEM, and ES-SMPS diameters. A plausible explanation for the smaller sizes found with DLS is that a permeable gel layer forms on the particle surface. Results from nanoparticle tracking analysis were strongly biased towards larger diameters, most likely because the silica particles provide low refractive index contrast. Calculations confirmed that the sensitivity is, depending on the shape of the laser beam, strongly size dependent for particles with diameters close to the visualization limit.

Geographically distributed classification of surface water chemical parameters influencing fate and behavior of nanoparticles and colloid facilitated contaminant transport.

The current production and use of nanomaterials in consumer products have increased the concern about the possibility that these enter the rivers during their entire life cycle. Further, many aquatic contaminants undergo partitioning to the ubiquitous aquatic colloids. Here is presented the development of a set of European water types for environmental risk assessment of chemicals transported as nanovectors as is the case of environmental fate of manufactured nanoparticles and colloid-bound contaminants. A compilation of river quality geochemical data with information about multi-element composition for near 800 rivers in Europe was used to perform a principal component analysis (PCA) and define 6 contrasting water classes. With the aid of geographical information system algorithms, it was possible to analyse how the different sampling locations were predominantly represented within each European water framework directive drainage basin. These water classes and their associated Debye-Hückel parameter are determining factors to evaluate the large scale fate and behaviour of nanomaterials and other colloid-transported pollutants in the European aquatic environment.

Potential scenarios for nanomaterial release and subsequent alteration in the environment.

The risks associated with exposure to engineered nanomaterials (ENM) will be determined in part by the processes that control their environmental fate and transformation. These processes act not only on ENM that might be released directly into the environment, but more importantly also on ENM in consumer products and those that have been released from the product. The environmental fate and transformation are likely to differ significantly for each of these cases. The ENM released from actual direct use or from nanomaterial-containing products are much more relevant for ecotoxicological studies and risk assessment than pristine ENM. Released ENM may have a greater or lesser environmental impact than the starting materials, depending on the transformation reactions and the material. Almost nothing is known about the environmental behavior and the effects of released and transformed ENM, although these are the materials that are actually present in the environment. Further research is needed to determine whether the release and transformation processes result in a similar or more diverse set of ENM and ultimately how this affects environmental behavior. This article addresses these questions, using four hypothetical case studies that cover a wide range of ENM, their direct use or product applications, and their likely fate in the environment. Furthermore, a more definitive classification scheme for ENM should be adopted that reflects their surface condition, which is a result of both industrial and environmental processes acting on the ENM. The authors conclude that it is not possible to assess the risks associated with the use of ENM by investigating only the pristine form of the ENM, without considering alterations and transformation processes.